To contact us, fill out your enquiry and details in the boxes below.
*If you would like to contact us from outside the UK, please select the appropriate country flag in the top menu and contact your local Avon team.
I WOULD LIKE TO KNOW MORE ABOUT:
Have you visited our tyre care section yet? Maybe these can help to answer your questions by reading our Frequently Asked Questions.
Have you visited our advice section on our Motorcycle Tyre Care Page’?
For fitment enquiries, please check out our Motorcycle fitment guide. Simply enter your bike make and model on our homepage to see our advised fitments.
Avon would not normally recommend this fitment. If you do this however, due to the way tyres are manufactured, you should reverse the tyre’s direction of rotation if you fit a front tyre on the rear or a rear tyre on the front of your bike. During tyre manufacture, a length of tread rubber is wrapped around the carcass and joined together with an angled bevel type joint. This joint is orientated so that as the tyre rotates, this joint stays shut. As the rear tyre provides drive and the front tyre provides braking, the joint is made one way for the rear tyre and the opposite way for the front. Fitting incorrect tyres could cause potential MOT/insurance issues and may affect the bikes handling capabilities.
Track pressures for 3D Ultra Xtreme are:
Recommended Hot pressures using tyre warmers:
Front - 32-34psi
Rear - 26-28psi
Cold pressures (no tyre warmers):
Front - 30-32psi
Rear - 24-26psi
28 front and 30 rear is good for the smaller scooters and 30 and 32 for the bigger scooters would be a good suggested psi.
Yes, when new m/c tyres are fitted, they should not be subjected to maximum power until a reasonable 'running in' distance has been covered. 100 dry miles (160km) is the recommended minimum (discount any wet miles covered). Tyre should then be visually examined and their inflation pressure re-checked before riding.
The British Rubber Manufacturers Association advise tyres should be used within 6 years of manufacture. The tyre should then be removed after a total of 10 years. Avon recommend tyres should be used within 5 years of manufacture. The tyre should then be removed after a total of 7 years.
We call this Inverted Front Grooves. We have done a great deal of testing and research on tread patterns and found the front tyre is better run in the opposite direction to the rear. The front tyre has to deal with braking forces and the rear wheel with drive forces, which are basically opposite forces. This may make the front appear to be running the wrong way round but in wet tests, we have found that the footprint is not long enough for water to channel very far through the grooves, it just needs to be expelled sideways quickly. By running the tyre as we do, we significantly reduce irregular tread wear. This means that even when the tyre is half worn, it is still putting down the correct amount of rubber on the road. Tyres run the other way round suffer from stepped and irregular wear which reduces their footprint and effectiveness in the wet quite dramatically.
If you check out any of the latest sports radial tyres from any of the other main tyre manufacturers, you will see they are all starting to do the same.See IFG, (Inverted front grooves) section here.
Due to the modern materials used in the construction of these tyres, we normally recommend 25-28 psi front and 28-34 psi rear.
We would recommend increasing pressures by 1-2psi front and 2-3 psi rear.
To measure your rim width, measure inside of rim flange to inside of opposite rim flange.
WM1-1.6"WM2-1.85"WM3-2.15"WM4-2.5"
Yes, but only to the combinations below:-
Front Rear
Radial Radial
Bias Radial
X-ply Radial
Bias Bias
X-ply Bias
X-ply X-ply
This is difficult to answer as riding styles, torque etc. all contribute to tyre wear. As a rule of thumb:
Supersport 3,000 – 4,000 Miles
Sport 4,000 – 5,000 Miles
Sport Touring 4,000 – 8,000 Miles
Cruiser 7,000 – 15,000 Miles
X-ply 7,000 – 15,000 Miles
For all warranty or tyre return enquiries, under consumer law you must first contact your tyre dealer to allow them the opportunity to assess the tyres. This is the standard complaints procedure for the tyre industry.
For further information on the returns process applicable to the UK industry, please visit: https://btmauk.com/consumer-complaints-tyres/
For further information on the returns process applicable to Europe, please visit: http://www.etrto.org/Information/Useful-Documents
If you require further information please complete the below contact form.
Avon
Bath RoadMelkshamWiltshireSN12 8AA